Cleveland Specialty Inspection Services, Inc.

Cleveland Specialty Inspection Services, Inc.

A2LA Accredited Certificate Number 3039.01

Certification & Calibration...

 

Calibration and Inspection is performed in a controlled laboratory environment, by technicians using established industry procedures. Measurement equipment is calibrated using standards that are directly traceable to the National Institute of Standards and   Technology.  All calibrations and history records are maintained in accordance, with  ANSI/NCSL Z540-1, ISO 10012-1 and other applicable standards.

When placing orders specify the type of certification you require.  Please contact us for pricing.

 

 

 

  • Angle Plates
        
    up to 24 inches
  • Cylindrical Squares
        
    up to 18 inches
  • Contoureader Master
  • Depth Micrometer Master
        
    .5 to 5.5 inches
  • Dial Bore Gages
  • Dial Indicator/Test Indicators
  • Dial Vernier Calipers
         Length Standards - up to 48 inches
  • 60 Thread Mic Master
  • Levels
  • Micrometer Master(O.D.) Tree Type
         up to 12 inches
  • Mike Master Set 1-2-3 inch
  • Vernier Master Int. & Ext.



     
  • Radius Gages
  • Pitch Gages
  • Rules
         Up to 24 inches
  • Parallels and Straight Edge
         up to 48 inches
  • Plain Plug Gages
         (checked to 5 decimal places)
         up to 9 inch
  • Plain Ring Gages
         (checked to 5 decimal places)
         up to 12 inch
  • Protractors
  • Setting Master Discs
         up to 15 inch
  • Sine Bars
  • Squares
         (Granite or Steel) (.002 in./ft)
         Up to 24 inch
  • Micrometers
         (Outside, Inside & Depth)
  • Pin Gage Sets
         Long form Certs - actual listed for
         each pin.
         Short Form Certs. - gages out of
         Tolerance will be listed only.
  • Height Gages (Vernier)
         12 inch
         18 inch
         24 inch
  • Height Gages (Cadillac)
         12 inch
         18 inch
         24 inch
  • Thread Plug Gages
  • Work or Set Master (60)
         up to 6 inch
  • Thread Ring Gages (60)
         up to 6 inch

SET PLUGS MUST BE FURNISHED TO CHECK P.D.

Taper Pipe Gages
(NPT, ANPT, NPTF)

  • Thread Plug Gages
         up to 6 inch
  • Thread Ring Gages
         up to 3 inch
  • Plain Taper Plug or Ring
         up to 3 inch
  • Vee Blocks
         up to 6 inch
  • Surface Finish
         Ra

 

 

 

 

TERMINOLOGY

Short Form Certification (Straight Threads)
     Certificate indicates required and actual pitch diameter only.

Long Form Certification (Straight Threads)
     Certificate indicates required and actual measurements of pitch diameter, major diameter, minor diameter, flank angles and lead where they apply.

Short Form Certification (Taper Pipe Threads)
     Thread Plug - check P.D. at gage point and basic step.
     Thread Ring - check stand off to plug gage.
     Plain Taper Plug - check size at small end and basic step.
     Plain Taper Ring - check size at large end of basic step.

Long Form Certification (Taper Pipe Threads)
     Thread Plug - check P.D. at gage point, O.D. at small end, lead, angles, taper and steps.
     Thread Ring - check standoff to plug gage, angles, lead and minor diameter.
     Plain Taper Plug - check size at small end, taper and steps.
     Plain Taper Ring - check size at large end and steps.

Note: Call for quotation on inspection and calibration requirements not listed.  First article inspection is quoted on individual order.

CSIS Limitation of Liability:  Services are performed on equipment that is traceable to the National Institute of Standards and Technology.  CSIS is responsible for inspection service results only at the time of service, utilizing generally accepted industry procedures and under the environmental and other conditions of inspection at that time in its facility.  As dimensions of the  product are affected by usage and varying environmental changes CSIS makes no claims about customer product or property once it leaves CSIS environment.  Once, the product or other property leaves CSIS facility, customer assumes total responsibility for assuring that it continues to meet customer specifications through appropriate quality assurance procedures.

 

 

 

[Site Home] [About Us] [Products] [Gages] [Services] [Quality] [Contact Us] [Mobile] [E-mail]

CLEVELAND SPECIALTY INSPECTION SERVICES, INC.

8562 East Avenue

Mentor, Ohio 44060

Phone: (440) 974-1818          Fax: (440) 974-6828

 

Copyright© 1998 Cleveland Specialty Inspection Services, Inc. - all rights reserved

 

Site designed by:  LANCOM Technologies LLC